EN   | 中文

Home Products News Contact Us
Home / News

What Are The Precautions After Replacing The Brake Pads?

Mar. 04, 2019

Ceramic Disc Brake Pad is a very important part of a car. It is related to the safety of cars and people. Many people know how to replace the brake pads, but can you achieve good braking effect after replacing the brake pads? What else do you need to do? Below is the BMW Disc Brake Pad Wholesaler.

Due to processing and assembly errors, the frictional resistance of the moving parts of the new car is always much larger than normal under the initial operation. The initial running-in (also called the running-in) effect of the car, the service life, work reliability and economy of the car Sex will have a big impact. Therefore, the new brake pads must be strictly enforced when they are used.

1. The running-in rules for driving new brake pads within 1000 km:

(1) It is not allowed to drive at full speed.

(2) Generally, it is not allowed to drive at speeds exceeding 100 km/h.

(3) Avoid running at idle speed in each gear.

(4) Running-in regulations for vehicles running between 1000 and 15,000 km: they can be gradually increased to speed or at the allowable speed of the engine.

2. After the running-in period, you should pay attention to:

(1) When driving a car with a tachometer, switch to the adjacent high-speed gear, when the pointer reaches the red indicator zone, the engine will allow a high speed of 5,500 rpm for a short time. The speed allowed for each gear is: first gear 40 km / h, second gear 65 km / h, third gear 100 km / h, fourth gear 135 km / h, fifth gear 165 km / h.

(2) Avoid running the engine at an unnecessarily high speed. Early switching into the high speed gear will help save fuel and reduce noise.

(3) The engine speed should not be too low when driving, and only when the engine is working hard, it will be replaced by the low gear.

(4) The speed and speed listed in the manual are only applicable to engines with normal temperature. When cold, do not operate the engine at higher speeds, whether in neutral or in other gears.

(5) New tires do not have adhesion at the beginning of use. Therefore, new tires also need to be engaged. The speed should be slower when driving for the first 100 kilometers. The method of driving should also be cautious.

(6) The new brake lining also needs to be run-in. When the first 200 km is driven, it does not have the ideal friction. At this stage, if the braking effect is slightly worse, the pedal pressure can be appropriately increased. This situation also exists after each replacement of the brake lining.

(7) Under the possible conditions, long-term continuous driving should be avoided during the running-in of the new brake pads, so as to avoid the continuous working time of the engine and the chassis parts, which will cause the wear of the parts to be intensified, which directly affects the service life of the vehicle. It is also necessary to avoid full-load operation, generally operating within 80 km of the rated load within the first 1000 km of travel. In addition, we must try to avoid high-speed driving. In the first 2,000 km, the throttle speed should not exceed 70% of the high speed.

(8) During the running of the new car, the driver should warm up in the original place after the initial start of the new car. After the water temperature rises to the working temperature range, the driver should start again. When driving, choose good road surface. When the road condition is poor, slow down and slow down; To be smaller, the operation should be light. Once the sound of the brake pad engine or the chassis is abnormal, stop the inspection and stop the malfunction in the bud.

IK2110034:1605434,GDB1783,D1404,D1557,OPEL Disc Brake Pads Manufacturer

Contact Us
  • +86 203 6278 400
  • +86 208 0675 884
  • canddy@gzifk.com
  • Add. : A310, Bo feng business building, 818 Cong Yun Road, Baiyun District, Guangzhou. China. 510420
Follow Us

Copyright © Guangzhou IFK Auto Parts Co., Ltd All Rights Reserved Sitemap 

Whatsapp

Skype

QQ